Page 1 of 1

MM-X-DRIVER="is not valid

Posted: Tue Apr 06, 2010 7:22 pm
by Tha Ra
Hello,
I'm trying to run MiniMyth 0.22.0-72 a VIA Epia-V board with an Ubuntu backend.
When I try to boot, I get the following error:

Code: Select all

MM-X-DRIVER="is not valid
MM-X-DRIVER="is not valid

init failed. check '/var/log/messages' for further details.
The messages file containt the following:

Code: Select all

Apr  6 20:16:56 NAS kernel: [110539.901662] eth0: link up.
Apr  6 20:16:59 NAS pulseaudio[1210]: ratelimit.c: 52 events suppressed
Apr  6 20:16:59 NAS dhcpd: DHCPDISCOVER from 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:00 NAS dhcpd: DHCPOFFER on 192.168.0.53 to 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:01 NAS dhcpd: DHCPREQUEST for 192.168.0.53 (192.168.0.1) from 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:01 NAS dhcpd: DHCPACK on 192.168.0.53 to 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:53 NAS dhcpd: DHCPDISCOVER from 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:54 NAS dhcpd: DHCPOFFER on 192.168.0.51 to 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:54 NAS dhcpd: DHCPREQUEST for 192.168.0.51 (192.168.0.1) from 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:54 NAS dhcpd: DHCPACK on 192.168.0.51 to 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:57 NAS dhcpd: DHCPDISCOVER from 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:57 NAS dhcpd: DHCPOFFER on 192.168.0.51 to 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:57 NAS dhcpd: DHCPREQUEST for 192.168.0.51 (192.168.0.1) from 00:40:63:cb:a9:1a via eth0
Apr  6 20:17:57 NAS dhcpd: DHCPACK on 192.168.0.51 to 00:40:63:cb:a9:1a via eth0
This is my minimyth.conf file:

Code: Select all

MM_X_OUTPUT_VGA='auto'
MM_THEME_NAME='blue'
MM_THEMEOSD_NAME='Gray-OSD'
MM_DHCP_TCODE='Europe/Amsterdam'
MM_DHCP_HOST_NAME='minimyth'
MM_DHCP_NTP_SERVERS='0.nl.pool.ntp.org'

Re: MM-X-DRIVER="is not valid

Posted: Sun Apr 11, 2010 4:01 pm
by gollywog
Hi,

How are you editting your config? In Linux or Windows? I had similar issues and the problem was simply using windows to edit the config. There is a dos2unix tool that you can install on your ubuntu box and pass the config file through it. Then all the carriage returns etc will be sorted.

Gollyowg

Re: MM-X-DRIVER="is not valid

Posted: Sat Apr 17, 2010 4:20 pm
by Pablo
I assume you mean MM_X_DRIVER not MM-X-DRIVER. If you are using MM-X-DRIVER, then that would be a problem.

My understanding is that the VIA EPIA-V boards use the CLE133 for graphics, which does not have MPEG2 hardware acceleration and has a relatively underpowered processor. As a result, MiniMyth does not support it.